The 6.4-Inch Brooke of CSS Tennessee at Naval Station Norfolk
A 6.4-Inch Brooke Rifle which was captured aboard CSS Tennessee is displayed at Naval Station Norfolk alongside an identical 6.4-Inch Brooke from CSS Albemarle.
The Tennessee Brooke was manufactured at Tredegar in June 1863 and was sent to Richmond Naval Ordnance Words for banding and rifling in August of 1863. It’s registry number is 49 and it’s Tredegar Foundry Number is 1853 (Olmstead et al. pg. 219).
6.4-Inch Brooke Rifle, S85, at Linwood Cemetery, Columbus, Georgia
6.4-Inch Brooke Rifle S-85 is mounted at Linwood Cemetery in Columbus, Georgia overlooking a section of Civil War graves. This Brooke was manufactured at the Selma Naval Gun Foundry in Selma, Alabama in 1864-1865. In March of 1865 it was sent to Columbus, Georgia to become part of the armament of the ironclad ram CSS Jackson which had been launched in December 1864. However, CSS Jackson would be captured by United States Army Cavalry under Major General James Wilson in April 1865 following the Battle of Columbus, one of the last battles of the American Civil War.
The 6.4-Inch Brooke Rifle of Jackson, Alabama
A 6.4-Inch Brooke Rifle cast at Selma in 1864 is displayed at Jackson, Alabama. It was cast on August 9th, 1864 and delivered to Mobile on December 21st, 1864 (see Daniel & Gunter, pg. 83). According to the historical marker placed next to the cannon, S96 was mounted at Oven Bluff on the Tombigbee River.
The 6.4-Inch Brooke of CSS Albemarle at Norfolk
A 6.4-Inch Brooke Rifle carried aboard CSS Albemarle is displayed at Naval Station Norfolk flanking a flagpole with another 6.4-Inch Brooke which was carried aboard CSS Tennessee. This Brooke likely was carried by CSS Albemarle during the Battle of Plymouth and Battle of Albemarle Sound in 1864.
8-Inch Brooke Smoothbore, S-26, at Gainesville, Alabama
An 8-Inch Double Banded Brooke Smoothbore, S26, manufactured at the Selma Naval Gun Foundry in 1863-1864 may be found beside the Old Cemetery in Gainesville, Alabama. S26 was cast as a 6.4-Inch Brooke Rifle. According to Messers Olmstead, Stark, and Tucker, S26 was one of three blocks (raw castings) intended to be produced as 6.4-inch rifles which encountered difficulties during machining but were successfully salvaged as 8-inch smoothbores. S26 is the only survivor of the three Selma produced 8-Inch Brooke Smoothbores.
The 6.4-Inch Brooke at Historic Tredegar
A Double Banded 6.4-Inch Brooke Rifle is displayed outside of Historic Tredegar Ironworks in Richmond, Virginia where it was originally manufactured in 1862.
The Brooke in Richmond is marked with the Tredegar foundry number 1633 and as weighing 9,400 pounds as manufactured. Number 1633 was cast at Tredegar on or about July 26th, 1862.
The Brooke Rifles of CSS Tennessee
Four Brooke Rifles carried aboard CSS Tennessee at the Battle of Mobile Bay are displayed as trophies at the Washington Navy Yard. One other is displayed at Selma, Alabama. Another may be found at Naval Station Norfolk.
The Single Banded Brooke Rifles of CSS Atlanta
Four Brooke Rifles captured from CSS Atlanta are displayed as trophies at the US Navy's Washington Navy Yard.
6.4-Inch Brooke Rifle at Fort Pulaski
A 6.4-Inch Double Banded Brooke Rifle is displayed at Fort Pulaski near Savannah, Georgia.
The Guns of CSS Peedee
Three cannon recovered from the wreck of CSS Peedee (including a Dahlgren which saw service on USS Southfield) are on display at the Florence County Veterans Center in Florence, SC.
6.4-Inch Brooke Rifle in Richmond, Virginia
A 6.4-Inch Brooke Rifle is displayed at The American Civil War Museum at Historic Tredegar in Richmond, Virginia